Follow the assembly video and the instructions below to set up your Snow Joe SJ618E 18-inch, 13-amp electric snow thrower. Assemble the handle frames, connect the chute crank rods, and install the discharge chute and deflector before use.
Watch the Assembly Video
Watch the SJ618E assembly walkthrough below.
Having trouble viewing the video? Watch on YouTube.
Before You Begin
Unpack the snow thrower and confirm that the following parts are included: snow thrower with upper handle, middle frame, lower frame, discharge chute, chute deflector, upper crank rod, lower crank rod with cotter pin, crank rod connector, eight handle/deflector knobs, two square J-bolts, six carriage bolts, two thumbscrews, and one chute screw.
Important safety warning: Keep the snow thrower disconnected from electrical power during assembly. Inspect the wiring before assembly. If wiring is damaged or damage is suspected, do not assemble or operate the unit. Handle the wiring carefully to prevent damage.
Assemble the Upper, Middle, and Lower Frames
-
Align the Upper Handle
Align the holes in the upper handle with the holes at the top of the middle frame (manual Fig. 1).
-
Secure the Upper Handle
Insert two carriage bolts and tighten two handle knobs on the outside of the unit (manual Fig. 2).
-
Align the Middle and Lower Frames
Align the holes in the middle frame with those at the top of the lower frame (manual Fig. 3).
-
Secure the Middle Frame
Insert two carriage bolts and tighten two handle knobs on the outside of the unit (manual Fig. 4).
-
Position the Lower Frame
Align the holes at the bottom of the lower frame with the mounting holes on the snow thrower (manual Fig. 5).
-
Fasten the Lower Frame
Secure the lower frame using two square J-bolts and two handle knobs. Install these knobs on the inside of the unit and tighten (manual Fig. 6).
Assemble the Chute Crank
-
Remove the Cotter Pin
Remove the cotter pin from the lower crank rod (manual Fig. 7).
-
Insert the Lower Crank Rod
Insert the pin-hole end of the lower crank rod into the opening at the back of the housing, aligning the holes (manual Figs. 8–10).
-
Secure the Lower Crank Rod
Reinsert the cotter pin to secure the lower crank rod (manual Figs. 11–12).
-
Slide on the Connector
Slide the crank rod connector over the top of the lower crank rod (manual Fig. 13).
-
Tighten the First Thumbscrew
Align the connector’s bottom hole with the hole in the lower crank rod. Insert the first thumbscrew and turn it clockwise to secure (manual Fig. 14).
-
Route the Upper Crank Rod
Slide the upper crank rod through the rubber ring on the middle frame (manual Fig. 15).
-
Join the Crank Rods
Slide the upper crank rod into the top of the crank rod connector (manual Fig. 16).
-
Tighten the Second Thumbscrew
Align the holes in the connector and upper crank rod. Insert the second thumbscrew and turn it clockwise to secure (manual Fig. 17).
Install the Discharge Chute and Deflector
-
Lock the Discharge Chute
Align the lower chute with the slot in the collar, then rotate it clockwise into the locked position (manual Figs. 18–19).
-
Secure the Discharge Chute
Fasten the chute using the supplied screw (manual Fig. 20).
-
Position the Chute Deflector
Place the deflector over the discharge chute and align the mounting holes (manual Fig. 21).
-
Fasten the Chute Deflector
Install the carriage bolts and deflector knobs, then tighten. Make sure each carriage bolt is fully seated in the chute’s square hole before tightening (manual Fig. 22).
Final Assembly Check
Confirm that all frame knobs, carriage bolts, J-bolts, thumbscrews, and chute fasteners are secure. Make sure the lower crank rod’s cotter pin is installed, the discharge chute is locked into the collar, and the chute deflector is firmly attached. Check that the wiring was not damaged during assembly. Review the manual’s electrical safety and operating instructions before connecting power.
Need the Operator’s Manual?
For assembly diagrams (Figs. 1–22), electrical safety requirements, and complete operating instructions, see the Shop Joe Product Manuals page and search for SJ618E.
Need Help Assembling Your SJ618E?
Contact Shop Joe Customer Care for assistance if parts are missing, components do not align, or wiring appears damaged.