If your Sun Joe cordless chemical sprayer will not start, has little or no spray, leaks, or has an uneven spray pattern, use the model-specific checks below. These products use liquid chemical solutions for supported cleaning or garden applications; they are not paint sprayers.
Models Covered + Power Type
Model differences: The SJ-APS-1G and SJ-APS-2G have internal 4V batteries and 20-inch wands. The 24V-GS-LTW and 24V-GS-CT use a 24V IONMAX battery platform and telescoping spray wands (17.7–28.7 inches). The 24V-GS-CT is tool-only; the 24V-GS-LTW kit includes a battery and charger.
Before Troubleshooting
Quick Troubleshooting Sequence
-
Confirm the Exact Model
Read the model number on the sprayer. The 4V models charge through their built-in battery system; the 24V models use removable IONMAX batteries. Do not apply 24V battery-removal steps to 4V units.
-
Check the Power Source
For SJ-APS-1G and SJ-APS-2G, charge the internal 4V battery using the supplied charging equipment. For 24V-GS-LTW and 24V-GS-CT, confirm a compatible charged 24V IONMAX battery is correctly installed. The CT tool-only product does not include a battery or charger.
-
Check the Tank and Solution
Confirm there is liquid in the tank and that the tank and cap are properly seated. The 4V models have 1- or 2-gallon tanks; the 24V models have 1-gallon tanks. Follow the chemical manufacturer’s instructions for preparation and dilution.
-
Check the Wand, Hose and Connections
With the sprayer off, inspect the wand and accessible hose connections for visible blockage, disconnection or leakage. Do not operate with cracked or damaged components.
-
Adjust and Check the Spray Nozzle
The official product descriptions specify adjustable jet-to-fan nozzles. Turn the nozzle to the desired spray pattern; inspect for residue or blockage with the unit off. Follow the model manual for nozzle cleaning.
-
Test Again Safely
Reassemble the sprayer as described in its manual and test using only an approved liquid in a suitable location. If the issue continues, stop and contact support.
Troubleshooting by Symptom
Sprayer does not turn on
Check the applicable power source: recharge the internal 4V battery on SJ-APS-1G/SJ-APS-2G, or check installation and charge of the removable 24V battery on 24V-GS-LTW/24V-GS-CT. If it still does not start, stop and contact Customer Support.
Little or no liquid comes out
Check tank contents, proper tank installation, wand and hose connections, and the adjustable nozzle for blockage. Clean accessible components only as instructed in the applicable operator’s manual.
Spray pattern is too narrow or too wide
Adjust the twist nozzle between concentrated jet and fan spray. The 24V models also have a telescoping wand and rotating wand end; set these as needed for the application.
Liquid leaks from the sprayer
Switch off. Check that the tank cap, wand and hose connections are correctly seated and inspect for visible cracks. Do not continue using the unit if leakage persists or parts are damaged.
Sprayer stops during use
Check remaining liquid and the applicable battery charge. If the motor or battery is unusually hot, produces smoke, or smells burnt, stop immediately and contact Customer Support.
Nozzle appears blocked
Switch off, remove the battery on 24V models, and follow the model’s operator’s manual for nozzle cleaning. Do not attempt to clear the nozzle while the sprayer is running.
Chemical application is uneven
Check the nozzle setting (jet versus fan), solution level and visible hose/wand connections. Follow the chemical product label for application requirements and dilution.
Official Model References and Manuals
Use the product page for the exact model. Official operator’s manuals are listed under Product Attachments on the relevant Shop Joe pages where available; consult the manual before disassembly, cleaning or servicing.
- SJ-APS-1G — Official Shop Joe Product Page
- SJ-APS-2G — Official Shop Joe Product Page
- 24V-GS-LTW — Official Shop Joe Product Page
- 24V-GS-CT — Official Shop Joe Product Page
When to Stop Using the Sprayer
- Any tank, hose, wand, nozzle or housing is cracked, broken or continues to leak.
- There is smoke, a burning odor, abnormal heat, sparks or unusual motor noise.
- Battery or electrical components appear damaged.
- Cleaning and checks described in the applicable manual do not restore normal operation.
Escalation Path
If the issue persists, contact Shop Joe Customer Support. Have the exact model number (SJ-APS-1G, SJ-APS-2G, 24V-GS-LTW or 24V-GS-CT), the liquid used, the symptom and the applicable battery/charging information ready.